大颗粒磷钼酸铵:制备与结晶动力学(英文)

通过缓慢滴加焦磷酸钾的硝酸溶液到钼酸铵溶液中制得了大颗粒磷钼酸铵(AMP)。研究了AMP的成核速率(G)与晶体生长速率。与晶体生长速率相比成核速率的反应级数更高。最初,大颗粒磷钼酸铵的结晶过程处于相变反应控制的动力学区域,此时溶液的过饱和生成速率比过饱和消除速率高。晶体线生长速率与溶液的过饱和度先增加后降低。在滴加中期,过饱和消除速率增长到与其生成速率相当。在滴加后期,晶体成核速率快速增高,而晶体的线生长速率下降。晶体的成核速率成为过饱和消除的唯一控制步骤。因此,AMP成核大部分是在首先接触到滴加液的局部溶液中完成的。     

环烷酸对油水界面膜流变性质的影响研究

研究了环烷酸对油水界面膜界面张力、弹性模量、损耗模量以及界面膜破裂速率常数的影响,同时对环烷酸与沥青质之间的相互作用进行了测定。结果表明,环烷酸使得原油油水界面张力下降;弹性模量随着环烷酸加量以及振荡频率的增加都分别逐渐增大,并且最终都趋于平衡;在任何振荡频率值时,损耗模量都随着环烷酸加量先增大后减小;当环烷酸加量增加时,界面膜破裂速率常数降低。环烷酸与沥青质之间存在相互作用,随着环烷酸加量的增加,其对沥青质界面膜弹性模量的影响与对原油界面膜弹性模量的影响相似,表明环烷酸主要是通过与沥青质相互作用而促进乳状液稳定性的。     

α-四(对磺酸钠苯氧基)酞菁锌(钴,镍)光敏剂的光动力性质研究

采用UV-Vis光谱、红外吸收光谱、CHN元素分析及激光解析飞行时间质谱对α-四(对磺酸钠苯氧基)酞菁锌(钴,镍)[α-PhSPcZn(Co,Ni)]进行表征.在光诱导条件下,采用四甲基偶氮唑蓝比色法(MTT法),考察了光敏剂的中心原子、浓度和光照时间等条件下对癌细胞的抑制作用.结果显示,光照15min、浓度为0~100mg·L-1范围内时,α-PhSPcZn的抑瘤率高于α-PhSPcCo和α-PhSPcNi.抑瘤率均随光照时间和配合物浓度的增加而升高,α-PhSPcZn的抑制率可达54%,其IC50值为75mg·L-1.     

1,3-双[3-(1-甲氧基-2-羟基丙氧基)丙基]封端聚硅氧烷的合成

以1,3-双[3-(1-甲氧基-2-羟基丙氧基)丙基]四甲基二硅氧烷和八甲基环四硅氧烷(D4)为原料,通过阳离子催化开环聚合制备了1,3-双(3-(1-甲氧基-2-羟基丙氧基)丙基)封端聚硅氧烷,研究了反应温度,反应时间,催化剂种类及加入量对于聚合反应的影响,结果表明,最佳反应条件为:反应温度65℃,反应时间24h,浓硫酸作为催化剂加入量为反应物质量的0.3%,此时反应拥有最高的转化率。通过红外光谱与核磁共振光谱对产物进行了表征。     

Effects of GC temperature and carrier gas flow rate on on‐line oxygen isotope measurement as studied by on‐column CO injection

Although deemed important to δ¹⁸O measurement by on‐line high‐temperature conversion techniques, how the GC conditions affect δ¹⁸O measurement is rarely examined adequately. We therefore directly injected different volumes of CO or CO–N₂ mix onto the GC column by a six‐port valve and examined the CO yield, CO peak shape, CO–N₂ separation, and δ¹⁸O value under different GC temperatures and carrier gas flow rates. The results show the CO peak area decreases when the carrier gas flow rate increases. The GC temperature has no effect on peak area. The peak width increases with the increase of CO injection volume but decreases with the increase of GC temperature and carrier gas flow rate. The peak intensity increases with the increase of GC temperature and CO injection volume but decreases with the increase of carrier gas flow rate. The peak separation time between N₂ and CO decreases with an increase of GC temperature and carrier gas flow rate. δ¹⁸O value decreases with the increase of CO injection volume (when half m/z 28 intensity is <3 V) and GC temperature but is insensitive to carrier gas flow rate. On average, the δ¹⁸O value of the injected CO is about 1‰ higher than that of identical reference CO. The δ¹⁸O distribution pattern of the injected CO is probably a combined result of ion source nonlinearity and preferential loss of C¹⁶O or oxygen isotopic exchange between zeolite and CO. For practical application, a lower carrier gas flow rate is therefore recommended as it has the combined advantages of higher CO yield, better N₂–CO separation, lower He consumption, and insignificant effect on δ¹⁸O value, while a higher‐than‐60 °C GC temperature and a larger‐than‐100 µl CO volume is also recommended. When no N₂ peak is expected, a higher GC temperature is recommended, and vice versa. Copyright © 2015 John Wiley & Sons, Ltd.     

A sample preparation method for recovering suppressed analyte ions in MALDI TOF MS

In matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI TOF MS), analyte signals can be substantially suppressed by other compounds in the sample. In this technical note, we describe a modified thin‐layer sample preparation method that significantly reduces the analyte suppression effect (ASE). In our method, analytes are deposited on top of the surface of matrix preloaded on the MALDI plate. To prevent embedding of analyte into the matrix crystals, the sample solution were prepared without matrix and efforts were taken not to re‐dissolve the preloaded matrix. The results with model mixtures of peptides, synthetic polymers and lipids show that detection of analyte ions, which were completely suppressed using the conventional dried‐droplet method, could be effectively recovered by using our method. Our findings suggest that the incorporation of analytes in the matrix crystals has an important contributory effect on ASE. By reducing ASE, our method should be useful for the direct MALDI MS analysis of multicomponent mixtures. Copyright © 2015 John Wiley & Sons, Ltd.     

气基磁化焙烧回收包头稀土尾矿中铁的研究

试验采用磁化焙烧-磁选的方法来回收包头稀土尾矿中的Fe。考察了还原球团的粒径、焙烧温度、还原气体的成分、还原气气体流量、焙烧时间对于磁化焙烧回收Fe的影响。在焙烧温度为580℃,CO与CO2的浓度比为40∶60,还原气体气流量为1.2 L·min-1,焙烧时间为60 min的条件下对球团进行磁化焙烧,并将焙烧后的球团进行磨矿,使得-200目的物料占物料总重量的95%。将磨矿后的物料置于磁场强度为233 k A·m-1的磁选管中进行磁选,可以得到品位为60%左右的铁精矿,其铁回收率达到70%左右。     

Theoretical study on the degradation mechanism of methamidophos and chloramine phosphorus with OH radicals

Theoretical investigation on the gas‐phase degradation reaction mechanism of methamidophos (MAP) and chloramine phosphorus (CHP) with OH radicals is performed. The equilibrium geometries and the harmonic vibration frequencies of the stationary points are obtained at M06‐2x/6‐31+G(d,p) level, and the higher‐level energetic information is further refined at M06‐2x/6–311++G(3df,2p) level. The rate constants for the 14 reaction channels are calculated by the improved canonical variational transition state theory with small‐curvature tunneling correction over the temperature range 200–2000 K. The three‐parameter expressions of k₁(T) = 1.53 × 10^?19T^2.74exp(?1005.12/T), k₂(T) = 1.36 × 10^?20T^3.02exp(?1259.56/T) are given. The total rate constants of all reaction channels of MAP with OH radicals are in good agreement with the available experimental data. Our results indicate that the H‐abstraction reactions on methyl are the major channels for the reaction of MAP and CHP with OH radicals. © 2015 Wiley Periodicals, Inc.     

Dependency of dynamic interlaminar shear strength of composites on test technique used

Studies are presented on dependency of dynamic interlaminar shear (ILS) strength on the experimental technique used for a typical plain weave E-glass/epoxy composite. Dynamic ILS strength was determined based on two experimental techniques, namely torsional split Hopkinson bar (TSHB) apparatus using thin walled tubular specimens and compressive split Hopkinson pressure bar (SHPB) apparatus using single lap specimens. The results obtained from these techniques are compared. In general, it is observed that dynamic ILS strength for composites obtained by TSHB testing using thin walled tubular specimens is lower than the dynamic ILS strength obtained using single lap specimens in compressive SHPB. The issues involved in TSHB testing of thin walled tubular specimens made of composites are discussed and the reasons for reduced dynamic ILS strength using thin walled tubular specimens are highlighted. Finite element analysis (FEA) of thin walled tubular specimens made of composite and resin subjected to quasi-static torsional loading is presented. Using FEA results, the reasons for lower ILS strength of composite thin walled tubular specimens are substantiated.     

Synergistic effect of maleimido phenyl urea derivatives mixed with some commercial stabilizers on the efficiency of thermal stabilization of PVC

Four novel antimicrobial maleimido phenyl urea stabilizers 1–4 were synthesized from N-[4-(chlorocarbonyl) phenyl] maleimide with phenyl urea and its derivatives (p-methyl, o-chloro and p-carboxy). The effect of mixing maleimido phenyl urea stabilizer 2 with each of the reference stabilizers, dibasic lead carbonate (DBLC), cadmium-barium-zinc stearate (Cd-Ba-Zn stearate) or n-octyltin mercaptide (n-OTM), on the stabilization efficiency in thermal degradation of rigid PVC at 180 °C in air, has been investigated. Mixing was effected in the range of 0–100 wt% of stabilizer 2 relative to each of the reference stabilizers. The stabilizing efficiency was evaluated by measuring the length of the thermal stability period (Ts), the period during which no detectable amount of hydrogen chloride gas could be observed, and also from the rate of dehydrochlorination as measured by continuous potentiometric determination, and by the extent of discoloration of the degraded polymer samples. The results show a true synergistic effect from the combination of stabilizer 2 with any of the reference stabilizers. Mixing of the stabilizers improves the Ts values, decreases the rate of dehydrochlorination and lowers the extent of discoloration of the polymer. The maximum synergism was attained when stabilizer 2 is mixed with either of the three reference stabilizers in equivalent weight ratio (50%/50%). The observed synergism may be attributed to the different mechanisms by which the investigated and the reference stabilizers work.